Reed Relay Schematics A

Contact
Form

Model
Number

Nominal
Coil
Voltage
VDC

Must
Operate
Voltage
VDC max

Must
Release
Voltage
VDC min

Coil
Resistance
+/- 10%
@ 25C

Width

Schematic Top
View ^{2, 8}

End to End Coil

Schematic Top
View ^{2, 8}

Same End Coil

7101

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

300
1600
4200

.410
(10.41)

7102

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

150
1000
3500

.500
(12.70)

7103

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

100
800
2400

.660
(16.76)

7000s3L

7000s3R

7104

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

80
550
2000

.760
(19.30)

7000s4L

7000s4R

1B¹

7121

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

150
1000
3500

.500
(12.70)

7000s5L

7000s5R

2B¹

7122

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

100
800
2400

.660
(16.76)

7000s6L

7000s6R

7141

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

175
1100
4200

.410
(10.41)

7142

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

65
490
1550

.660
(16.76)

7000s8L

7000s8R

7143

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

55
300
1350

.760

(19.30)

7000s9L

7000s9R

1A
Latch^5,6

7150

5
12

3.75
9.0

0.4
1.0

550/550
1750/1750

.500
(12.70)

7000s10L

7000s10R

1A1B^5,7

7160

5
12
24

3.75
9.0
18.0

0.4
1.0
2.0

80
550
2000

.760
(19.30)

7000s11L

7000s11R


	7000 Series Schematics Page 2


	Get It In .PDF Format

Notes:
⁵ These relays contain bias magnets. Correct coil polarity must be observed.
⁶Coil suppression diode is required for proper operation. Correct coil polarity must be observed.
⁷ Break before make not guaranteed.
⁸Dot stamped on top of relay refers to pin #1 location. E-pin indicates Electrostatic shield pin. Unused pins omitted. Pin numbers for reference only.
⁹ All models with Hg wet contacts are position sensitive, must be mounted within 30⁰ of vertical plane. See schematic.


	[Home] [Relays] [Switches] [Sales] [Literature] [Contact Us]


		Coto Technology 171 Service Road, Suite 301 Warwick, RI 02886-1015 401-943-2686 FAX: 401-942-0920


	Coto Technology BV Jan Campertstraat 11 6416 SG Heerlen, The Netherlands +31 45 5439345 FAX: +31 45 5427216