Reed Relays 9011, 9012 & 9117 Series


	Miniature Molded SIP Reed Relays The 9012 package dimensions are 47% smaller than standard 9000 SIPs, yet the relay retains the 10W switch ratings of its larger counterparts. The 9011 package dimensions are 65% smaller than the standard 9000 SIPs and incorporates Coto's 7mm switch rated at 3W. The 9117 goes one step further, reducing package size by 65% from standard 9000 SIPs. This is the smallest SIP footprint with a 3W rating. These miniature SIP relays are ideal for use in ATE applications and other high reliability test, measurement and telecommunications applications where high board density and long life are key requirements.

		Series Features u 9012 is a 10W SIP relay ( .400" x .150" x .400" ) u 9011 is a 3W SIP relay ( .400" x .150" x .265" ) u 9117 is the smallest 3W SIP relay (.270"x .150" x .385") u Magnetic shielding reduces interaction u Optional coil suppression diode protects coil drive circuits u UL File #E67117 u High insulation resistance 10¹²W minimum u High Speed Switching u Molded thermoset body on integral lead frame design u High reliability, hermetically sealed contacts for long life


	9011, 9012 & 9117 Miniature Molded SIP Relay Mechanicals


	Dimensions in Inches (Millimeters)


	Model 9011


	Model 9012


	Model 9117


	2


	9011, 9012 & 9117 Miniature SIP Relay Specifications Table

Model Number			9011^2,4	9012^2,4	9117^2,4
Parameters	Test Conditions	Units	(3 Watt) 4 Pin SIP	(10 Watt) 4 Pin SIP	(3 Watt) Narrow Fit
COIL SPECS.
Nom. Coil Voltage		VDC	5 12	5 12	5
Max. Coil Voltage		VDC	6.5 15.0	6.5 15.0	6
Coil Resistance	+/- 10%, 25° C	W	500 750	500 750	400
Operate Voltage	Must Operate by	VDC - Max.	3.75 9.0	3.75 9.0	3.75
Release Voltage	Must Release by	VDC - Min.	0.4 1.0	0.4 1.0	0.5
CONTACT RATINGS
Switching Voltage	Max DC/Peak AC Resist.	Volts	100	200	100
Switching Current	Max DC/Peak AC Resist.	Amps	0.250	0.5	0.25
Carry Current	Max DC/Peak AC Resist.	Amps	0.5	0.5	0.5
Contact Rating	Max DC/Peak AC Resist.	Watts	3	10	3
Life Expectancy-Typical¹	Signal Level 1.0V, 10mA	10⁶ Ops.	250	1000	250
Static Contact Resistance (max. init.)	50mV, 10mA	W	0.150	0.120	0.120
Dynamic Contact Resistance (max. init.)	0.5V, 50mA at 100 Hz, 1.5 msec	W	0.200	0.200	0.200
RELAY SPECIFICATIONS
Insulation Resistance (minimum)	Between all Isolated Pins at 100V, 25°C, 40% RH	W	10¹²	10¹²	10¹²
Capacitance - Typical Across Open Contacts		pF	0.7	0.7	0.14
Open Contact to Coil		pF	1.4	1.4	N/A
Dielectric Strength (minimum)	Between Contacts Contacts to Coil	VDC/peak AC VDC/peak AC	200 1500	200 1500	150 1500
Operate Time - including bounce - Typical	At Nominal Coil Voltage, 30 Hz Square Wave	msec.	0.35	0.35	0.20
Release Time - Typical	Zener-Diode Suppression³	msec.	0.10	0.10	0.10


		Top View: Grid = .1"x.1" (2.54mm x 2.54mm)

	Get It In .PDF Format

Notes: ¹Consult factory for life expectancy at other switching loads. Resistance >0.5W defines end of life or failure to open. ²Optional diode is connected to pin #2 (+) and pin #3 (-) for 9011 & 9012; pin #1 (+) and pin #2 (-) for 9117. Correct polarity must be observed. ³Consists of 56V Zener diode and 1N4148 diode in series, connected in parallel with coil. ⁴9011 & 9117 external mag shield. 9012 internal mag shield.




		Environmental Ratings Storage Temp:-35°C to +100°C; Operating Temp:-20°C to +85°C Solder Temp: 270°C max; 10 sec.max The operate and release voltage and the coil resistance are specified at 25°C. These values vary by approximately 0.4%/°C as the ambient temperature varies. Vibration: 20 G's to 2000 Hz; Shock: 50 G's


	[Home] [Relays] [Switches] [Sales] [Literature] [Contact Us]


		Coto Technology 171 Service Road, Suite 301 Warwick, RI 02886-1015 401-943-2686 FAX: 401-942-0920


	Coto Technology BV Jan Campertstraat 11 6416 SG Heerlen, The Netherlands +31 45 5439345 FAX: +31 45 5427216